XTREME OUTLAW CHASSIS WORKS
KEITH FEDIRKO - PRESIDENT
7923 Route 873 Slatington, PA 18080 phone : 484-553-6031 or phone : 610-760-9161
NEW CAR BUILD !
NEW OUTLAW 10.5 HEMI POWERED VIPER!
SCREW BLOWN 10.5 OUTLAW NOVA IN FOR UPDATES!
COMING IN THE FALL!
SUPERCHARGED V10 VIPER MOTOR ,6 SPEED, BACK HALF, PRO STREET
1973 PLYMOUTH ROAD RUNNER!
2013 STATE OF THE ART ULTRA LIGHTWEIGHT PRO NITROUS CAMARO!
FULTON POWERED 1969 OUTLAW 10.5 CAMARO!
2013 STATE OF THE ART ULTRA LIGHTWEIGHT PRO XTREME CAMARO!
10% OFF Sale
On All Santhuff Products
Santhuff Struts And Spindles On Sale!
Early GM Spindle Stock Suspension Design
15 degree Superstock Style Coil Over Strut w/Spindles
'82-'92 Camaro Bolt in Super Stock Struts
1990-2004 Mustang Bolt In Struts
Bolt in Mustang 2005 and Newer Coil Over Struts
Tube Chassis Coil Over Struts
Santhuff Rear Shocks On Sale!
Rear Double Adjustable Coil Over Shocks
1st Gen Camaro / Nova Front Double Adjustable Coil Over Shocks
1st Gen Camaro / Nova Front
4th Gen Camaro Front
Mopar Double Adjustable Shocks
All Strange Engineering Parts On Sale !
Strange Engineering Double Adjustable Shocks With Springs .
Part # STGE-6050
Sale Price $630.00
Strange Engineering Single Adjustable Shock Without Springs
Part # STGE-6051
Price $338.00 Pair without springs
Sale Price $321.00 without springs
Strange Engineering Front Spindle Mount Brake Kit.
Part # STGE-6153
Sale Price $525.00
Strange Engineering Ultra Center Section
RF225 3.812 bore Aluminum Ultra Case fully assembled with lightweight 40 spline (2.250 bearing journal) spool, billet aluminum pinion support,3.40-4.86 large stem Pro 9310 gear set & chrome molly yoke
Part # STGE-6200
Sale Price $1655.00
5% OFF Sale
On All Mark Williams Rears
Mark Williams Driveshafts On Sale!
Mark Williams Thrid Members On Sale!
Pro Mod Assembly (9-1/2")
Aluminum thru-bolt case (3.812" bore), 40-spline lightweight steel spool, MW steel 1350-series pinion yoke, ball bearing pinion support, 1/2" ring gear bolts, your choice of 4.11 to 4.86 large pinion Richmond 9-1/2" Pro gears.
Pro Mod Assembly (9")
Aluminum thru-bolt case (3.812' bore), 40-spline lightweight steel spool, steel
MW 1350-series pinion yoke, ball bearing pinion support, your choice of 3.20
to 4.86 large pinion 9" Richmond Pro gears.
Super Gas/E.T. Bracket Assembly
Aluminum thru-bolt case (3.250" bore), lightweight steel spool, MW 1350-series
pinion yoke, ball bearing pinion support, your choice of 3.89 to 4.86 large pinion
9" Richmond Pro gears.
Pro Stock Assembly (9-1/2")
Aluminum thru-bolt case (3.812" bore), 40-spline aluminum spool, steel MW
1350-series pinion yoke, ball bearing pinion support, your choice of 4.86 to 5.43 standard pinion 9-1/2" Richmond Pro gears.
Mark Williams Brake Kits On Sale!
Tony Dirose Black Ice 55 Chevy
NEW SHIRTS AND COLORS FOR XTREME OUTLAW CHASSIS WORKS!
Outlaw 10.5 1970 Dodge Challenger!
New State Of The Art Design 10.5 Outlaw Chassis.
Xtreme Outlaw Chassis Works Featured In Dragzine!
CLICK HERE TO READ STORY!
Jean Roger's Blown Small Block BMW !!
55 BLOWN PRO MOD CHEVY
Welcome to Xtreme Outlaw Chassis Works, LLC
Contact: Keith Fedirko
Xtreme Outlaw Chassis Works is excited to announce the Master Chassis Builders from VPRC have joined our staff!! We are now producing Pro Mod dual frame rail chassis, Top Sportsman single frame rail chassis and Three-Quarter chassis for 10.5 Outlaw!!
Xtreme Outlaw is now taking orders for chassis and complete race cars. If we do not have your body style available, we can custom build your chassis with the measurements you provide. Other chassis shops won’t, but we will! That’s the Xtreme Outlaw Difference!!
We bring the best-quality chassis on the planet to our customers and we promise our trademark professional, high-quality customer service on every order you place--EVERY customer is our “biggest customer.”
For more information about Xtreme Outlaw chassis, call 610-760-9161 or log onto www.xtremeoutlaw.com and send us an email with your requirements. Contact us today to take advantage of the Xtreme Outlaw Difference!!
Dual Frame Rail Chassis Single Frame Rail Chassis
On Roll Bars And Roll Cages Installed
6 Point Roll Bar Mild Steel : From $600.00
6 Point Roll Bar Chrome Moly : From $850.00
Save over $225.00
10 Point Mild Steel Roll Cage : From $1,300.00
10 Point Chrome Moly Roll Cage : From $1,600.00
Save over $400.00
For Roll Bars and Roll Cages.
SIDE-BAR CLEVIS & TUBE FOR 1-3/4X.134"ROLL BARS
Price $125.00 Each
SWING-OUT CLEVIS SET,1-5/8X.134"ROLL CAGES
Price $79.00 Each
REMOVABLE-BACK-BRACE BRACKET KIT,1-5/8 -.134
Price $80.00 Each
Body And Chassis Package!
Package includes Dual Frame Rail Pro Mod Chassis, Body, the body mounted the doors mounted with all the hardware,front end mounted,with rocker tin mounted.
With engine plate and mid plate and engine plate mount kit,mid plate mount kit mounted.
4-Link brackets,shock tabs,Ani-Roll Bar mounts,upper and lower strut mounts,rack mounts,with trans mount.
All makes and models of bodies are available call for pricing.
price base on a 63 Corvette fiberglass body.
Pro-Mod Dual Frame Rail SFI 25.1E Chassis Kits
Shown With opitions
All of our in house chassis are assembled and Heli-Arc welded by our Master Chassis Builders on our full surface jig-fixture.
All of our chassis, unwelded or welded, comes with F/C cage, engine plate and mid plate mounts, rack & pinion mounts, upper strut mounts and lower control arm tabs, upper shock mounts and anti-roll housing built into the chassis,front 4-link brackets.
Price Welded : $8,645.00
Price Unwelded : $2,225.00
Top Sportmans Single Frame Rail SFI 25.1E Chassis Kits
Great for Pro Stock, Super Gas and Bracket Cars.
All of our chassis, unwelded or welded, come with F/C cage, engine plate and mid plate mounts, rack & pinion mounts, upper strut mounts and lower control arm tabs, upper shock mounts and anti-roll housing built into the chassis,front 4-link brackets.
Price Welded : $6,725.00
Price Unwelded : $1,950.00
Three-Quarter SFI 25.2 Chassis Kits
The Three Quarter Chassis has been designed and developed specifically for the Outlaw 10.5 racers. The chassis ties into the factory front frame and meets all SFI 25.2 specs.
When you want to professionally back half your car, this is the state of the art design. Available welded or in kit form, with brackets and tabs for engine plate, mid plate,transmission mount,4-link, anti-roll mounts, shock mounts. The remainder of the chassis comes loose for installation by the customer.
Price Welded : $3,850.00
Price Unwelded : $1,750.00
X-Links Now Instock!
The X-link is a sliding "X" that spreads the load out to the four corners and not corner to middle which puts all the load on one heim end, like the old fashioned Wishbone system. All Four corners have 5/8" heim ends, so failure is not a problem like the Wishbone.
For todays high horse power Pro Mod, Pro Stock, Outlaw 10.5, the X-Link is the strongest rear end centering device available on the planet.
18" X 24"
20" X 24"
20" X 28"
X-Link Kit w/CM Heims Price : $500.00
Unwelded X-Link Kit w/CM Heims Price : $275.00
Mickey Thompson Slicks
Part # 3169W
Sale Price $265.00
Carbon Fiber Products
Carbon Fiber Wheel Tubs 47"
Check out these awesome carbon fiber wheel tubs. Construction is hand laid carbon cloth and fire retardant resin. All tubs feature a Cormat Liner to protect the perfect exterior finish. All carbon fiber tubs have passed certification with IHRA and NHRA and come with serial numbers. Two sizes now available for your convenience. 47" Diameter, 27" wide, 23.5" tall. An extra $30.00 box fee is added if these are shipped. Weight: 10lbs.
Carbon Fiber Sheet
Produced in the composite shop, these carbon fiber flat sheets are of the highest standard in the industry. Use these sheets to create custom panels and finishing touches on your car. Approx. thickness is .060"
Weight: 11 lbs.
Use these anywhere on the chassis to enhance and protect the powder coat finish. Available in 60" lengths to cover tubing diameters 1.25" - 1.375"
Use these anywhere on the chassis to enhance and protect the powder coat finish. Available in 60" lengths to cover tubing diameters 1.25" - 1.375" - 1.5" - 1.625" - 1.75" and 2". Please specify tube diameter when ordering.
Carbon fiber Seat
This seat has a 1" flange around the edge for added strength. Constructed from carbon fiber, core, Kevlar and vacuum processed to ensure the highest quality part.
Comes in a high gloss carbon fiber finish.
Dimensions are 29" tall, 23.5" wide @ the top & 18.5" wide @ the bottom.
Weighs just 2.9 pounds!
Stroud Safety Products On Sale!
Drag Chute Pricing
|Boat Chute Fire Proof||$415|
|Fuel / Alcohol Dragster||$445|
|Fuel / Alcohol Funny||$465|
The chutes listed above may be upgraded with with either an air or spring launcher for an additional $310 now.
|Carbon Fiber Air Launcher||$450|
|Launcher Upgrade with Air or Spring||$370|
|Launcher Upgrade with Air or Spring||$365|
Originally designed by Stroud Safety, the Engine Diaper comes in either the SFI approved professional style or the original ballistic nylon sportsman style. Use a Stroud Engine Diaper to keep parts and pieces away from places they don’t belong! Available for all engine and oil pan combinations, for all type cars.
Stroud Safety builds supercharger restraints for almost all applications. All are SFI approved for 14.1 and 14.2.
The 14.1 unit (shown) is for the bracket racer that needs minimal restraint for his class. It comes complete with header mounts and adjustable straps and fits either a 6-71 or 8-71 supercharger. Other sizes are also available.
The 14.2 unit fits 6-71, 8-71, 10-71, 12-71 and 14-71 blowers. The kit consists of the top plate, blower bag and all the fittings to attach to the motor. The blower strap anchors are the new Stroud type, with the blower strap having the locking pins sewn to it, preventing the loss of the locking pins.
Remember, we re-certify all Stroud Safety products!
Sanders Engineering Racing Wheels
740 Series Front Wheels
7401535A - 15" Spindle mount wheel to fit Anglia spindle 3.5"wide
7401535S - 15" Spindle mount wheel to fit Strange spindle 3.5" wide
7401722A - 17" Spindle mount wheel to fit Anglia spindle 2.2" wide
Add "-BLK" after part number for Black anodizing.
760 Series Heavy Duty 16" Diameter Wheels
Available with 4.25" Back Spacing
24 bolt Bead Lock System
SFI 15.3 or 15.4
Rear Wheels 3pcs 16" Wide
Part Number Example: "76016HD164250DBL"
760 Series Wheel
16 for 16" Diameter Wheel
HD for Top Fuel SFI 15.4 (H3 for high horsepower SFI 15.3)
16 for 16" Wide Wheel
42 for 4.2" Back Spacing
50 for 5 on 5.0" Bolt Circle (55 for 5.5")
DBL for Double Bead Lock
750 Series 15" Diameter Double Bead Lock Wheels
16 bolt Bead Lock System
Rear Wheels 3pcs 8" to 16" Wide (in 1" increments)
Part Number Example: "75015124045DBL"
750 Series Wheel
15 for 15" Diameter
12 for 12" Wide (8" thru 16")
40 for 4" Back Spacing (1" thru 7" BS)
45 for 5 on 4.5" Bolt Circle (47 for 4.75", 50 for 5.0" and 55 for 5.5")
DBL for Double Bead Lock
New Stainless Steel Race Muffler
Many sizes to choose from ( 3" 31/2" 4" 5" inlet/outlet )
Stainless Steel Race Muffler, 5" inlet/outlet x 5" long
T304 Stainless Steel
Price - $125.95 each
Sale Price $115.95
Weld Racing Wheels
Weld Alumastar 2.0 DBL Weld Alumastar 15" X 3-1/2"
Wheel 16" X 16" Strange Spindle Mount
Part # WELD-6012 Part # WELD-6000
Our Price $1,403.31 Our Price $530.95
Sale Price $1,353.00 Sale Price $515.95
OUR ONLINE STORE
Xtreme Outlaw Chassis Works